Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revision | |
| bandsaw [2024/09/12 01:52] – jkowalczewski | bandsaw [2024/09/12 02:42] (current) – jkowalczewski |
|---|
| |
| |
| | {{ :actualfirstslide.jpeg?200 |}} Upon entering the woodshop, acquire protective wear: Safety goggles and ear muffs | {{:woodglueslide.jpeg?200 |}} Acquire wood glue from the 'Adhesives' shelf | {{ :tapemeasuresbox.jpeg?200 |}} Grab a tape measure from the main tool shelf under the 'W' section |{{:pencilsbox.jpeg?200 |}}Pick up a pencil for dimensioning from the 'Pencils/Sharpies' box || {{ :secondslide.jpeg?200 |}}Locate the bandsaw and your supplied wood for the activity | | | {{ :actualfirstslide.jpeg?200 |}} Upon entering the woodshop, acquire protective wear: Safety goggles and ear muffs | {{:woodglueslide.jpeg?200 |}} Acquire wood glue from the 'Adhesives' shelf | {{ :tapemeasuresbox.jpeg?200 |}} Grab a tape measure from the main tool shelf under the 'W' section |{{:pencilsbox.jpeg?200 | }} Pick up a pencil for dimensioning from the 'Pencils/Sharpies' box ||{{ :secondslide.jpeg?200 |}}Locate the bandsaw and your supplied wood for the activity | |
| | {{ :originaldimensioning.jpeg?200 | }} Dimension out a 6" x 6" square and mark spots of wood you will discard by using 'X's' | {{ :begincuttingslide.jpeg?200 | }} Begin cutting out your 6" x 6" square and be careful with your hand placement by using the edge on your wood farthest from the blade| {{:stopcuttingslide.jpeg?200| }} Upon reaching the first edge of your cut, stop the blade from cutting and back out of your wood. Do this for each side you cut. | |{{ :completecutpieces.jpeg?200|}} The two complete 6" x 6" pieces you should have cut| {{ :curvecutmeasure.jpeg?200 |}} Measure out diagonal from two corners to the top of one of the squares. The measurement does not need to be accurate, but needs around 4" - 5" of wood at the top at least. | | | {{ :originaldimensioning.jpeg?200 | }} Dimension out a 6" x 6" square and mark spots of wood you will discard by using 'X's' | {{ :begincuttingslide.jpeg?200 | }} Begin cutting out your 6" x 6" square and be careful with your hand placement by using the edge on your wood farthest from the blade| {{:stopcuttingslide.jpeg?200| }} Upon reaching the first edge of your cut, stop the blade from cutting and back out of your wood. Do this for each side you cut. | {{ :img_3295.jpg?200 |}} Further cutting of the 6" x 6" pieces. The cutting is inward from the side|{{ :completecutpieces.jpeg?200|}} The two complete 6" x 6" pieces you should have cut| {{ :curvecutmeasure.jpeg?200 |}} Measure out diagonal from two corners to the top of one of the squares. The measurement does not need to be accurate, but needs around 4" - 5" of wood at the top at least. | |
| |{{ :curvecutcompletepiece.jpeg?200 |}} The complete curve-cut piece that will attach to the base of the other 6" x 6" square.| {{ :glueapplication.jpeg?200 |}} Apply a THIN layer of wood glue to the bottom of the curve-cut wood piece. | {{ :clampedcurvedpieces.jpeg?200 |}} Attach the curve-cut wood to one of the ends of the 6" x 6" wood piece. Upon doing this, refer to the area beside the roll-up door where several clamps can be found and attach two on both of the backings of the wood corners to lock in place. Let sit for one hour|| {{ :completestuckpieces.jpeg?200 |}} Upon returning, unclamp both supports. | {{ :toolsbackup.jpeg?200 |}} Upon completing the bookend, return all tools to their respective places. | | |{{ :curvecutcompletepiece.jpeg?200 |}} The complete curve-cut piece that will attach to the base of the other 6" x 6" square.| {{ :glueapplication.jpeg?200 |}} Apply a THIN layer of wood glue to the bottom of the curve-cut wood piece. | {{ :clampedcurvedpieces.jpeg?200 |}} Attach the curve-cut wood to one of the ends of the 6" x 6" wood piece. Upon doing this, refer to the area beside the roll-up door where several clamps can be found and attach two on both of the backings of the wood corners to lock in place. Let sit for one hour|| {{ :completestuckpieces.jpeg?200 |}} Upon returning, unclamp both supports. | {{ :toolsbackup.jpeg?200 |}} Upon completing the bookend, return all tools to their respective places. | |
| |
